Ingot
IEC 61109 Standard EHV DC Transmission Tower Insulators 220kv High Strength
FXBW3-220/100-A to FXBW-220/210
Description
?
IEC 61109 Standard EHV DC Transmission Tower Insulators 220kv High Strength
?
?
Description:
?
1, 220kV tension suspension insulators are widely used in overhead transmission lines and substations
?
2, Dead end fittings are up to the requirements from the clients, usually we use ball, socket, tongue, clevis for tension insulators with forged steel or cast steel. The dimensions and coupling size can be exactly according to the specification requirements from the utilities.
?
3, The silicon rubber color of the insulators are also up to the requirements from the clients and all the silicon rubber materials past 5000 hours aging test silicon content test and hydrophobicity test.
?
4, ECR core rods are used in all the insulators, so we can guarantee a very good mechanical strength and anti-acid pollution performance for the insulators.
?
5, All our insulators were type tested and design tested in accordance with IEC61109, maximum RIV is 100μV when tested at 1MHz and10% over nominal line ground voltage for indicated system voltage.
?
6, All the 220kV tension suspension insulators are with two corona rings
?
?
Specifications:
?
Dimensions and Characteristics of 220kV composite polymer insulator
?
- - - -
Figure. No | Model | Rated Voltage | Specified Mechanical Load | Section Length | Insulating length | Minimum Creepage | Full-Wave Impulse Withstand Voltage (Peak) | 1 Min Wet Power Frequency Withstand Voltage | Weight (for Reference) |
? | ? | ? kV | ? kN | H mm | h mm | L mm | ≥ kV | ≥ kV | ? kg |
1.8-1 | FXBW3-220/100-A | 220 | 100 | 2150±30 | 1900 | 6300 | 1000 | 395 | 8.9 |
1.8-2 | FXBW3-220/100-B | 220 | 100 | 2150±30 | 1900 | 7300 | 1000 | 395 | 8.5 |
1.8-1 | FXBW4-220/100-A | 220 | 100 | 2240±30 | 1960 | 6400 | 1000 | 395 | 8.7 |
1.8-2 | FXBW4-220/100-B | 220 | 100 | 2240±30 | 1960 | 7650 | 1000 | 395 | 8.9 |
1.8-1 | FXBW-220/100 | 220 | 100 | 2240±30 | 1950 | 6800 | 1000 | 395 | 11.7 |
1.8-1 | FXBW-220/120 | 220 | 120 | 2240±30 | 1950 | 6800 | 1000 | 395 | 11.7 |
1.8-1 | FXBW-220/160 | 220 | 160 | 2340±30 | 1950 | 6800 | 1000 | 395 | 13.3 |
1.8-1 | FXBW-220/180 | 220 | 180 | 2340±30 | 1950 | 6800 | 1000 | 395 | 13.3 |
1.8-1 | FXBW-220/210 | 220 | 210 | 2340±30 | 1950 | 6800 | 1000 | 395 | 13.3 |
- - - -
?
?
Applications:
?
1, 220kV?EHV DC overhead transmission power lines.
?
2, 220kV??EHV DC substations
?
?
Competitive Advantage:
?
- - - -
The advantages of polymer/composite insulators over ceramic/porcelain insulators |
General comparison |
Factor | Ceramic/porcelain insulators | Polymer/composite insulators |
Weight | Heavy weight- For example 400kV - about 140kgs | 90% lighter than them but with same mechanical strength 400kV -- Around 15kgs |
Fragility | Highly fragility to shock and vibration | No fragility to shock and vibration |
Packing and transportation | Risky and very costly | Easy and economical |
Installation | Risky expensive and more labor required | Very easy and economical |
Handling | Difficult | Easy |
Maintenance cost | Very expensive | Low |
Vandalism | More susceptible | Highly resistant |
Breakages and secondary damage | Highly fragile- 10-15% breakages are reported during transportation storage and installation | Flexible and therefore highly resistant to breakages |
Technical comparison |
Mechanical failure | Reduction in mechanical strength and separation during to pings getting eroded | Just with single piece, so no such kind of problem |
Resistance to flashover and punctures | Low | High |
Anti tracking and erosion resistance | Very low- poor tracking resistance | Excellent tracking resistance avoids erosion or tracking of the housing material |
Dielectric strength | Lower than polymer | Excellent insulation performance |
Contamination and pollution | Highly effected | Not effected and has much longer life |
Hydrophobicity | No hydrophobicity, ceramic surface forms water films on the surface making easy path leading to more flashover | Very excellent hydrophobicity |
Self cleaning quality | No, dirty sand salt snow etc are easily attracted | Yes, due to hydrophobicity recovery characteristics |
Tension strength | Good | Better during crimping technology |
Maintenance | Needs maintenance like cleaning washing and greasing | Not required at all |
Safety | Are easy to explosion and breakages due to high fragile properties and stone throwing or gun shooting | Provide very high level of safety superior flexibility and strength. not easy to break due to stone throwing or gun shooting. |
- - - -
?
?
Read More
Jiangsu Xiangyuan Electric Equipment Co., Ltd.
Composite Polymer Insulator,Composite聽Suspension Insulator,Polymer Pin Insulator
Address: Group 3, Zhennan Village, Chaiwan Town, Rugao City,
Shenzhen, Guangdong
China, 518000
Tel: 86-755-26927358
Fax: 86-755-26927358
